Power systems · Power supply and control of stations

The electrical side of your pumping stations, from the substation to the motors.

Power supply, medium- and low-voltage equipment, motor control and protection, remote management: In All Africa (IN2A) equips and maintains pumping and irrigation stations.

The electrical work package of a pumping station

A pumping station is first of all an electrical installation: its pumps are driven by motors, often powerful ones, which must start, run and stop without damage to the grid or to themselves. In All Africa (IN2A) works on this electrical work package, from the power supply of the station to the panels that control the motors. The hydraulic design and the choice of pumps are the job of other specialists, with whom we coordinate.

Depending on the installed power, the station is supplied at low voltage or by its own transformer substation, connected to the medium-voltage grid. As pumping sites are often remote, the grid connection is part of the project. For the Aglou Centre residential tourist complex, near Tiznit, In All Africa (IN2A) installed a pumping station, including its monorail lifting hoist.

What our work covers

  • Power supply of the station: grid connection and MV/LV substation
  • Medium-voltage switchgear cubicles and equipment
  • Motor control and protection panels
  • Power and control cabling
  • Lighting and electrical installation of the rooms
  • Maintenance of the electrical and remote management equipment
The electrical work package of a station
  1. MV/LV substation
  2. Control panels
  3. Motors and pumps
  4. Level and pressure sensors
  5. Remote management

A model of principle: typical equipment, not the mock-up of a particular installation. Schematic diagram: it shows how the parts follow one another, not the drawing of a particular installation.

Controlling and protecting pump motors

Starting a pump motor draws a high current. The control panel keeps it in check through a starting method suited to the power of the motor, direct-on-line, soft start or variable speed drive, and protects the motor against overloads, short circuits and supply faults. On the most powerful stations, the motors may be supplied at medium voltage.

The automation then sequences the starts and stops according to the information received from the sensors, for example a level or a pressure, and reports faults to the operator. At the Doukkala high-lift pumping station (El Jadida), In All Africa (IN2A) supplied and replaced a voltage transformer cubicle and medium-voltage contactors for ORMVAD.

Remote management and maintenance of stations

Pumping stations and irrigation structures are scattered over large perimeters and are rarely staffed around the clock. Remote management sends the status of the equipment, the faults and the measurements back to a central station, and allows certain operations to be controlled from a distance. In All Africa (IN2A) maintained the remote management equipment of the Doukkala perimeter for ORMVAD.

A station that has stopped means a water supply that is interrupted. The maintenance of the electrical equipment (substation, cubicles, control panels) is therefore scheduled outside the periods when the station is in greatest demand. When an item of equipment reaches the end of its life, it is replaced without rebuilding the station: for ORMVAL, In All Africa (IN2A) replaced the electric hoist of the lifting systems of the SPCII station, in the Loukkos perimeter.

Your project, step by step

From the first site visit to the upkeep of the installation.

1

Station visit

We record the power supply available, the motors to be controlled, the equipment in place and the operating constraints of the station.

2

Electrical study

We size the power supply, the control and protection panels and the links, in coordination with the hydraulic designer.

3

Assembly and testing

Our teams install and connect the equipment, then test each motor and each automated sequence before commissioning.

4

Maintenance and renovation

We then maintain the electrical and remote management equipment, and replace items that reach the end of their life.

Our references

Client, scope of work and city, as they appear in our list of references.

ClientScope of workCityFields
ORMVADSupply and replacement of a voltage-transformer cubicle and medium-voltage contactors at the Doukkala high-service pumping station.Client attestation: 2013El JadidaMV/LV substations
ORMVADMaintenance of the remote-management equipment of the Doukkala perimeter.El JadidaMaintenance
ORMVALReplacement of the electric hoist of the lifting systems at the SPCII station, lower-hill sector of the Loukkos perimeter.Ksar El KebirPower systems
Aglou CenterInstallation of a pumping station, including the monorail hoist, at the Aglou Centre tourist residential complex.Client attestation: 2015TiznitPower systems

Pumping and irrigation: your questions

01What does In All Africa (IN2A) take care of in a pumping station?

Our work covers the electrical work package: power supply, medium- and low-voltage equipment, motor control and protection panels, automation and remote management. The hydraulic sizing and the choice of pumps are handled with the design office or supplier concerned, with whom we coordinate.

02How can a pumping station far from the grid be supplied?

Through a connection to the medium-voltage grid and a transformer substation dedicated to the station. In All Africa (IN2A) carries out overhead-to-underground and underground 22 kV connections and equips MV/LV substations. Near Tiznit, we reinforced the MV line supplying Aglou Centre and equipped two 315 kVA substations.

03What is remote management of a pumping station?

It is the monitoring and control of the station from a distance, from a central station: pump status, faults, measurements, start and stop commands. It saves journeys and flags an anomaly quickly. In All Africa (IN2A) maintained the remote management equipment of the Doukkala perimeter for ORMVAD.

04Can the electrical equipment of a station in service be modernised?

Yes. The cubicles, the contactors, the control panels or the lifting gear can be replaced without rebuilding the station. In All Africa (IN2A) did so at the Doukkala high-lift pumping station for ORMVAD, and at a station in the Loukkos perimeter for ORMVAL.

Let’s talk about your project

A station to equip or renovate?

A work package to price, a substation to renovate, a home to equip: tell us what you need and we will get back to you.